Go Back   Infamous Nissan - Hardbody / Frontier Forums > Search Forums

Showing results 1 to 25 of 500
Search took 0.04 seconds.
Search: Posts Made By: SBJ
Forum: Wiring and Electrical Today, 01:21 AM
Replies: 6
Views: 32
Posted By SBJ
You can also come up in front of the starter with...

You can also come up in front of the starter with a 14mm socket and a 6" extension. Get it seated on the bolt first then use a long flex head ratchet to crack it loose. It's kind of a pain to get to....
Forum: Hardbody Forum (D21) Today, 01:16 AM
Replies: 24
Views: 219
Posted By SBJ
For your misfire check that the wires aren't...

For your misfire check that the wires aren't burnt up on the end. I originally went with cheapo no-name wires and every few months the ends would burn up and need to be cut off. It did the exact same...
Forum: Hardbody Forum (D21) 05-13-2021, 05:55 PM
Replies: 23,014
Views: 1,684,181
Posted By SBJ
Don't German cars use lug bolts instead?

Don't German cars use lug bolts instead?
Forum: Hardbody Forum (D21) 05-13-2021, 03:38 AM
Replies: 23,014
Views: 1,684,181
Posted By SBJ
I think it's more common with aluminum/alloy...

I think it's more common with aluminum/alloy wheels. I had a car that needed hub-centric rings for the aftermarket wheels to center themselves on the hub. The lug holes were also small enough that it...
Forum: General Discussion 05-09-2021, 11:48 PM
Replies: 4
Views: 65
Posted By SBJ
There's also OBD eleven. It's nowhere near as in...

There's also OBD eleven. It's nowhere near as in depth as VCDS but it's fairly user friendly. I'd recommend trying to find a place that specializes in German cars. It'll probably be more expensive...
Forum: Introductions 05-07-2021, 11:42 PM
Replies: 4
Views: 66
Posted By SBJ
This. The bearing probably has a number on it you...

This. The bearing probably has a number on it you can use to find a replacement. 6203 is a common size for tensioner pulley bearings but always verify yours first.
Forum: Engine and Drivetrain 05-03-2021, 04:37 AM
Replies: 11
Views: 155
Posted By SBJ
A lot of transmissions have a test port where you...

A lot of transmissions have a test port where you can hook up a pressure gauge to measure the line pressure in various gears. I'd start there. Automatic transmissions need hydraulic pressure to apply...
Forum: Hardbody Forum (D21) 05-01-2021, 09:42 PM
Replies: 30
Views: 477
Posted By SBJ
You should be able to get a new center link for...

You should be able to get a new center link for less than $100. It's not a big deal at all to replace it.
Forum: Hardbody Forum (D21) 05-01-2021, 04:53 AM
Replies: 30
Views: 477
Posted By SBJ
If you need to fix the threads they're M12x1.25.

If you need to fix the threads they're M12x1.25.
Forum: Hardbody Forum (D21) 04-30-2021, 06:37 PM
Replies: 30
Views: 477
Posted By SBJ
Another thing you can do is crank down on the...

Another thing you can do is crank down on the puller until you think it's about to break then hit the forcing screw with a hammer. Sometimes the pressure combined with the sudden shock will be enough...
Forum: Hardbody Forum (D21) 04-29-2021, 03:20 AM
Replies: 10
Views: 220
Posted By SBJ
Some window screen under the cowl vents will help...

Some window screen under the cowl vents will help to keep leaves and pine needles out.
Forum: Hardbody Forum (D21) 04-27-2021, 04:40 PM
Replies: 8
Views: 154
Posted By SBJ
To add to that, one thing I like to do when...

To add to that, one thing I like to do when looking at a used car is to have someone else start the engine (cold) and look for smoke out the tailpipe.
Forum: Hardbody Forum (D21) 04-27-2021, 04:19 PM
Replies: 84
Views: 1,368
Posted By SBJ
If you are sure the distributor is in the correct...

If you are sure the distributor is in the correct position, put the engine at TDC on cylinder 1, then take the distributor cap off and mark the rotor and the body of the distributor. It'll save you a...
Forum: Hardbody Forum (D21) 04-27-2021, 06:46 AM
Replies: 84
Views: 1,368
Posted By SBJ
You'll need to get some new valve stem seals. OE...

You'll need to get some new valve stem seals. OE ones are probably the best choice given the amount of work involved in replacing them, but I have also had good luck with fel-pro seals in the past....
Forum: Hardbody Forum (D21) 04-27-2021, 04:51 AM
Replies: 84
Views: 1,368
Posted By SBJ
Do you feel anything binding if you spin the...

Do you feel anything binding if you spin the engine over with a ratchet? It's different than the normal resistance you feel from the compression, and you'll know it when you feel it. You can also...
Forum: Hardbody Forum (D21) 04-24-2021, 10:50 PM
Replies: 1
Views: 68
Posted By SBJ
It's technically a camshaft position sensor since...

It's technically a camshaft position sensor since the distributor rotates at the same speed as the camshaft. 96-97 models also have a crankshaft position sensor on the outside of the bellhousing. It...
Forum: Hardbody Forum (D21) 04-22-2021, 04:54 PM
Replies: 23,014
Views: 1,684,181
Posted By SBJ
Not techstream actually. I still need to get my...

Not techstream actually. I still need to get my hands on a cracked copy of it though.

The tool I used is a launch x431 v. They sell the same tool in a smartphone package called the diagun iv. I...
Forum: Hardbody Forum (D21) 04-22-2021, 03:43 AM
Replies: 23,014
Views: 1,684,181
Posted By SBJ
Thanks man. This was for a Toyota vehicle and...

Thanks man. This was for a Toyota vehicle and they are pretty straightforward to clone keys for. The blanks were ~$20 online plus a few more bucks to have a hardware store cut them. The actual...
Forum: Hardbody Forum (D21) 04-22-2021, 01:31 AM
Replies: 23,014
Views: 1,684,181
Posted By SBJ
Not D21 related but earlier I tried using one of...

Not D21 related but earlier I tried using one of my scan tools for something I haven't tried before...programming new keys. It was a success, and about $280 cheaper than the dealership wanted for two...
Forum: Nissan Cars 04-17-2021, 04:43 PM
Replies: 26
Views: 1,683
Posted By SBJ
I am pretty sure you can buy a small house in...

I am pretty sure you can buy a small house in some parts of the country for less than a new Tacoma costs. Used Toyota trucks are also stupidly overpriced for what they are. And I say that as someone...
Forum: Hardbody Forum (D21) 04-17-2021, 01:29 AM
Replies: 26
Views: 481
Posted By SBJ
Yep, the toughest part by far is the upper...

Yep, the toughest part by far is the upper starter bolt. Get that one out of the way first. There are a couple of ways to get to it. Either go through the wheel well with a long socket extension and...
Forum: Hardbody Forum (D21) 04-16-2021, 05:33 AM
Replies: 23,014
Views: 1,684,181
Posted By SBJ
Dang, that's cheap for one of those power...

Dang, that's cheap for one of those power stations. I've thought about making a crude one before using a deep cycle battery but I don't think I could do it for less than $170.

Scifi...I think...
Forum: Hardbody Forum (D21) 04-13-2021, 01:56 AM
Replies: 12
Views: 201
Posted By SBJ
Most of the lines are 5/32" or 4mm. Some of the...

Most of the lines are 5/32" or 4mm. Some of the bigger ones like the charcoal canister are 5/16" or 8mm. 20ft sounds about right, I went through 2 rolls of it when I did all mine.
Forum: Hardbody Forum (D21) 04-12-2021, 08:42 PM
Replies: 2
Views: 76
Posted By SBJ
I've always wondered if KA24E valve cover bolts...

I've always wondered if KA24E valve cover bolts would work. They are also shouldered like the Z24 bolts but use a 10mm head instead.
Forum: Hardbody Forum (D21) 04-07-2021, 11:01 PM
Replies: 23,014
Views: 1,684,181
Posted By SBJ
That's pretty bad. What's it out of? I've never...

That's pretty bad. What's it out of? I've never seen one actually break the valve off.
Showing results 1 to 25 of 500

 
Forum Jump

All times are GMT. The time now is 04:24 AM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2021, Jelsoft Enterprises Ltd.