Forum: Suspension
08-01-2019, 01:50 PM
|
|
Replies: 187
Views: 103,669
Glazy,
I would think that you will want an...
Glazy,
I would think that you will want an angled block of some kind in there when you do the redrill. I ended up just doing the drop leaves with a 3 degree shim on my truck, no additional blocks,...
|
|
Forum: Wiring and Electrical
07-31-2019, 02:44 PM
|
|
Replies: 64
Views: 2,485
Hi Nunya,
Your wiring theory is sound, except...
Hi Nunya,
Your wiring theory is sound, except for the large gauge wires that will be feeding your motors. 18Ga wiring (in my opinion) is not large enough to run the ~20A that are required for the...
|
|
Forum: Hardbody Forum (D21)
07-11-2019, 09:37 PM
|
|
Replies: 10
Views: 1,180
Hi Jstck,
This is the correct question "-If I...
Hi Jstck,
This is the correct question "-If I get an alternator (that may even have been on a KA24E) with a multirib pulley, will my V-belt pulley fit if I transplant it? Will it end up in the same...
|
|
Forum: Wiring and Electrical
06-27-2019, 07:35 PM
|
|
Replies: 8
Views: 496
Hi Flint,
I would start by eliminating the...
Hi Flint,
I would start by eliminating the dimmer. There will be 3 wires at the plug for the dimmer, 1 ground, 1 park lamp, 1 dash lamp. Jump the park lamp to the dash lamp and leave it...
|
|
Forum: Interior & Audio/Video
05-28-2019, 10:28 PM
|
|
Replies: 2
Views: 344
Hi KrAv,
True story. I cant see your pic...
Hi KrAv,
True story. I cant see your pic but,if the subs will handle the power your amp is making, the box is the single most important aspect of the build. I had a pair of $40 12s in my car on a...
|
|
Forum: Introductions
05-20-2019, 01:57 PM
|
|
Replies: 133
Views: 6,595
|
|
Forum: Introductions
05-14-2019, 01:41 PM
|
|
Replies: 133
Views: 6,595
EF2,
Since you have them apart now, you will...
EF2,
Since you have them apart now, you will want to re-index them to where the angle matches left to right....... Assemble everything else on the front end, get the upper a arms to rest on the...
|
|
Forum: Introductions
05-02-2019, 10:46 PM
|
|
Replies: 133
Views: 6,595
As far as looking like my wheel is pushed...
As far as looking like my wheel is pushed back..... yes you are not wrong. It is by exactly 1/2 of an inch. As far as looking wrong, my opinion is that it is not noticeable enough to bother me to try...
|
|
Forum: Introductions
04-26-2019, 02:50 PM
|
|
Replies: 133
Views: 6,595
Hi guys.
Here is the pictures you have asked...
Hi guys.
Here is the pictures you have asked for.
The redrill is NOT complicated. Yes 2 inches up and 1/2 inch back from original hole center. If you do not go back that 1/2 inch you can not go...
|
|
Forum: Hardbody Forum (D21)
04-23-2019, 10:00 PM
|
|
Replies: 14
Views: 947
|
|
Forum: Introductions
04-22-2019, 01:47 PM
|
|
Replies: 133
Views: 6,595
|
|
Forum: Introductions
04-19-2019, 02:24 PM
|
|
Replies: 133
Views: 6,595
|
|
Forum: Introductions
04-18-2019, 04:25 PM
|
|
Replies: 14
Views: 654
|
|
Forum: Introductions
04-18-2019, 03:11 PM
|
|
Replies: 133
Views: 6,595
Hi EF2,
I have the belltech spindles and...
Hi EF2,
I have the belltech spindles and leaves with a 4degree shim on my truck. The ride is very much stock, you will love it if you go that route.
Just a word of caution. If you are going to...
|
|
Forum: Suspension
04-10-2019, 03:41 PM
|
|
Replies: 20
Views: 1,626
|
|
Forum: Hardbody Forum (D21)
04-03-2019, 04:43 PM
|
|
Replies: 38
Views: 19,857
Sufarry, You have a few options here, go up...
Sufarry, You have a few options here, go up ~1.25" and back less than 1/2" or go up ~2" and back 1/2". Going back is mandatory if you want be able to go up as high as possible to get the perch...
|
|
Forum: Hardbody Forum (D21)
03-28-2019, 11:04 PM
|
|
Replies: 38
Views: 19,857
MLarson,
I measured 2"up and 1/2" back from...
MLarson,
I measured 2"up and 1/2" back from OEM hole center. I have the belltech 3" springs and they fit perfectly fine.
I did need a 4degree shim to correct my pinion angle though, FYI. I...
|
|
Forum: Hardbody Forum (D21)
03-27-2019, 02:18 PM
|
|
Replies: 11
Views: 446
|
|
Forum: Engine and Drivetrain
03-27-2019, 02:15 PM
|
|
Replies: 8
Views: 746
Hi Tom,
So if I were in your spot I would...
Hi Tom,
So if I were in your spot I would really dig into the Isuzu option. This will give you two upgrades, the Dana44 and rear disc brakes. It will have the side bonus of keeping the 6lug...
|
|
Forum: Hardbody Forum (D21)
03-25-2019, 01:07 PM
|
|
Replies: 2
Views: 230
Hi Paulie,
Yes. In my truck I used 1/4x4 flat...
Hi Paulie,
Yes. In my truck I used 1/4x4 flat steel to connect the sliders to each other through the factory mounts that bolt the sliders to the seat. Then drill new relocated holes to mount the...
|
|
Forum: General Discussion
03-22-2019, 06:55 PM
|
|
Replies: 5
Views: 272
Hi Cameron,
I have an 86 and had the EXACT...
Hi Cameron,
I have an 86 and had the EXACT same symptoms you describe in your OP. I was getting a code(I think 43) for injector failure from my ECM.
The problem on my truck was the wiring to the...
|
|
Forum: Hardbody Forum (D21)
03-19-2019, 08:52 PM
|
|
Replies: 11
Views: 446
Dan,
The 4x4 fenders should help, but I do...
Dan,
The 4x4 fenders should help, but I do think you may have to stretch the fender a bit to get it to clear the poke you have going on there. IIRC the 4wd fenders add ~1.25" to the bulge area...
|
|
Forum: Interior & Audio/Video
03-07-2019, 06:27 PM
|
|
Replies: 11
Views: 1,167
Your kit should have the contact plate that...
Your kit should have the contact plate that rides on the oem contact for the horn. The original wheel should have a set of contacts that look like spring-loaded fingers that ride on the multi-ring...
|
|
Forum: Wheels and Tires
02-25-2019, 02:56 PM
|
|
Replies: 4
Views: 476
Armand,
The correct fix for your problem...
Armand,
The correct fix for your problem would be to +1 the wheel size, like go to a pathfinder 15" wheel. The spindle manufacturers all state very clearly that the stock 14" should not be used...
|
|
Forum: Interior & Audio/Video
02-04-2019, 03:10 PM
|
|
Replies: 1
Views: 741
Hi GDLG,
If you are doing a like-for-like...
Hi GDLG,
If you are doing a like-for-like swap, round dash to round dash the parts should interchange. If you are doing a square dash to round dash swap this post should have most of the...
|
